User:Stever/boxford/speedsnfeeds
All recipes from personal experience and tested
Key
| Colour | Meaning |
|---|---|
| Blue | Not (proven) a maximum, could do more |
| Green | A demonstrated maximum, any more will break tools |
| Red | Known to be excessive, will break tools |
Aluminium
Roughing
| Tool Size/type | Material | Coating |
Surface speed (RPM) |
DOC | WOC |
FTP (feed rate) |
Comment |
|---|---|---|---|---|---|---|---|
| 12mm 4-flute flat end mill | HSS | Uncoated | 100m/min | 10mm | 4mm |
0.03 (250mm/min) |
Noisy and spindle only just copes, definitely a maximum, use conventional milling only. Limited by spindle power, not tool endurance |
| 5mm 4-flute flat end mill | HSS | Uncoated |
40m/min (2500rpm) |
5mm | 1.5mm |
0.02 (200mm/min) |
Good finish, not a maximum could have done more |
| 2mm 2-flute ball nose end mill | HSS | TiAlN coated |
19m/min (3000rpm) |
1mm | 0.5mm |
0.02 (120mm/min) |
Works OK, 150mm/min is too much |
Brass
Finishing
| Tool Size/type | Material | Coating |
Surface speed (RPM) |
DOC | WOC |
FTP (feed rate) |
Comment |
|---|---|---|---|---|---|---|---|
| 2mm 4-flute flat end mill | HSS | Uncoated |
19m/min (3000rpm) |
1 mm | 0.8mm |
0.01 (120mm/min) |
Nice surface finish |
| 60 degree 0.3mm tip engraver 1/8" shank | solid carbide | TiAlN coated |
25m/min (calculated) (2500rpm) |
N/A | 0.1mm |
0.02 (50mm/min) |
Probably can do more |
Slotting
| Tool Size/type | Material | Coating |
Surface speed (RPM) |
DOC |
FTP (feed rate) |
Comment |
|---|---|---|---|---|---|---|
| 4mm 4-flute flat end mill | HSS | Uncoated |
31m/min (2500rpm) |
1mm |
0.015 (150mm/min) |
Using ramp profile, might be able to do more but surface finish is not good |
H-13 Tool Steel
Roughing
| Tool Size/type | Material | Coating |
Surface speed (RPM) |
DOC | WOC |
FTP (feed rate) |
Comment |
|---|---|---|---|---|---|---|---|
| 6mm 4-flute flat end mill | solid carbide | TiAlN coated | 35m/min | 7mm | 0.5mm |
0.04mm |
Width is at maximum, depth might be deeper |
| 1mm 3-flute flat end mill | Solid Carbide | TiAlN coated |
9.4m/min (3000rpm) |
0.5mm | 0.5mm |
0.0022mm (20mm/min) |
Might handle more but only one test was made |
Finishing
| Tool Size/type | Material | Coating |
Surface speed (RPM) |
DOC | WOC |
FTP (feed rate) |
Comment |
|---|---|---|---|---|---|---|---|
| 20 degree 0.3mm tip engraver 1/8" shank | solid carbide | TiAlN coated |
30m/min (calculated) (3000rpm) |
0.5 mm | 0.15mm |
0.0026 (8mm/min) |
Too much, breaks the tip off |
Drilling
| Tool Size/type | Material | Coating |
Surface speed (RPM) |
FTP (feed rate) |
Comment |
|---|---|---|---|---|---|
| 6mm 2-flute jobber drill | HSS | TiN |
14m/min (730rpm) |
0.02mm (15mm/min) |
Was in danger of stalling spindle, definitely the maximum size that can be drilled in this material |