Anonymous user
Tools/mitresaw/induction: Difference between revisions
Updated from video of induction
imported>Stever No edit summary |
pi_wiki>Stever (Updated from video of induction) |
||
Line 17:
* Mention catch points: Most notably the knobs, the guard, and the blade itself.
* Goggles and ear protection is essential
* For larger projects or cutting treated timbers then a dust mask is a good idea, for cutting small amounts of regular timber it's optional
* Consider the risk of lead-based paints on reclaimed timber
* Use the air-filter above the bench when the mitre saw is in use.
|| Any loose hanging clothing or hair can get tangled, either pulling someone in or
|-
| Nomenclature ||
Line 36:
| Adjustment the saw for your cut ||
* Ensure the machine is switched off prior to all adjustments, and ensure that all locks are in place prior to switching on.
* To adjust the mitre, unscrew the knob and lift the handle at the end of the bed, adjust to a custom mitre angle between 0 and 57 degrees or use the slots at the base of the bed to adjust to 0, 15, 22.5, 30, or 45 degrees;
* To adjust the bevel angle, pull the lever located underneath the rail, then turn the unit counterclockwise until you are at the correct bevel angle.
* The compound slide position does not need to be adjusted, but when in use it should be extended as far out as is necessary prior to switching on, and when not in use it should be contracted as deep in as possible locked by twisting the red screw above the rail.
|| Getting the saw properly set up at the start is essential for safety and will make later adjustment easier
Line 45:
* Ensure all adjustments are complete and locked BEFORE startup.
* Connect up the blue scheppach shopvac to the dust extract port
** The dust extract isn't very good but it's better than nothing so use it
* Make sure the saw is plugged in, it uses a 110 V power source, which is why it's connected to a small yellow box (the transformer). It must not be used with extension leads.
* Position the wood in such a way that it is easily accessible and in the correct position without needing to reach in front of, under, or behind the saw.
** Clearance needs to long items.
* Hold the wood firmly against the fence, keeping your hands well clear of the red area, or use a clamp, and test that the blade lands in the correct position. Work must always be held firmly against the fence, freehand cutting of any sort is NOT ALLOWED.
* Consider the forces you are exerting to hold the work securely, ensure that if you slip or fall you will not move towards the blade
* If the work cannot be held securely against the fence in a way that can't rotate or move owing to it's size/shape/orientation, then it cannot be cut on the mitre saw, perhaps consider the [[Tools/tablesaw|table saw]] or [[Tools/bandsaw|bandsaw]] instead.
** This means round items and bits of tree are not normally suitable for this saw, consider using the bandsaw with suitable cribbing instead
* If the work has a high aspect ratio then consider what orientation to hold it in to avoid the saw kicking it up. Place the flatest parts of the wood on the bed and fence, with the narrowest flat side on the fence.▼
** Plastics are especially prone to snatching and causing dangerous situations so fixing and clamping must be better then for timber
* Always cut a bit before or after your line such that the edge of the blade is on the line and the centre is on the waste side, this ensures an accurate cut with minimal waste. Test this with both the laser, and by lowering the saw onto the work piece; the position of the saw takes priority over the laser, the laser is just a guide!▼
▲* If the work has a high aspect ratio then consider what orientation to hold it in to avoid the saw kicking it up. Place the
▲* Always cut a bit before or after your line such that the edge of the blade is on the line and the centre is on the waste side, this ensures an accurate cut with minimal waste.
* Consider where your sawdust and chips are going to go, warn people if necessary.
|| These considerations can significantly improve pleasantness for user, and those around them
Line 68 ⟶ 72:
| Cleaning up ||
* Switch the machine off at the socket.
* If you have large scraps, put them in the scrap bin, very large scraps go in the scrap pile by the door
* Use the dustpan for large accumulations of sawdust.
* Run the shopvac on and around the mitre saw, and lift the guard and clean underneath it as well.
* Where the bags for the Henry are kept and how to empty the scheppach
* If your timber has oily/greasy/paint-y residues on the bed the acetone can be used to clean the metal parts of the mitre saw.
|| Clean up ensures pleasant use and reduced fire risk.
| |||