Difference between revisions of "Tools/vinylcut"

From rLab Wiki
Jump to navigationJump to search
(Content from old Wiki)
(Manual)
Line 6: Line 6:
[[File:Graphtec cc330 01.jpg|250px|thumb|Graphtec Craft ROBO CC330 Vinyl Cutter]]  
[[File:Graphtec cc330 01.jpg|250px|thumb|Graphtec Craft ROBO CC330 Vinyl Cutter]]  


Placeholder Page.
The manual for the vinyl cutter is [[media:CC300m-UM-151.pdf|here]].  
__TOC__
__TOC__



Revision as of 10:12, 28 September 2018

Graphtec Craft ROBO Vinyl Cutter


This page has been noted as requiring attention to bring it up to the basic standard as per the guidance

Please remove this tag once this page has been improved that standard


Introduction

Graphtec Craft ROBO CC330 Vinyl Cutter

The manual for the vinyl cutter is here.

Current Status

Date Status Comment
10th September 2018 Functional

how to use it

The vinyl cutter is used to cut self-adhesive designs of various patterns (typically text and logos) to be stuck on to a workpiece. For more advanced usage it could also be used to make stencils for chemical processes or paint.

preparing the design

Prepare the design in Inkscape.

Set the document properties to units of mm (milimetres) - this will avoid confusion! Draw the design actual size. Obviously fill and colour don't matter, it only cuts outlines. If the design includes text, use the "Path -> Object to path" option in Inkscape to make paths. This applies also to any other object which is not a path. Ungroup everything before cutting (Inkcut doesn't like groups) Orientation - the cutter will cut ALONG the roll by default. This is not usually what you want for small pieces (width < 500mm). So rotate it 90 deg. If creating a very large design (e.g. 500mm high text), then leave the design "the right way up". Once everything is drawn and made into ungrouped paths, use the Inkcut extension.

setting up the machine

Turn it on Ensure connected Loading vinyl - make sure that the feed clamps are clamped in appropriate places. (Feed in vinyl from the back) Setting cut pressure - this is the parameter "p=" shown on the cutter screen. Set it so it cuts through the vinyl but not the backing. Use "test" button to check. Setting the origin - set the origin to the buttom *RIGHT* corner of the working area, not the bottom left! Offline the cutter Position the cutter head using the arrow buttons (Do not try to move manually) When in correct position, press the "zero" button Put cutter back online To test the machine, the "test" button cuts a small rectangle. You can use this to check (e.g. on newly loaded stock) that it's cutting through the vinyl cleanly

Connection via USB in Linux, means the device is probably /dev/ttyUSB0. Make sure that the serial baud rate is set to the same on the PC in Inkcut, as on the front panel menu. (see Tech Details below) Ensure you have read/write permissions to /dev/ttyUSB0, this can be done by running sudo chmod 777 /dev/ttyUSB0

applying vinyl to workpiece

There is a roll of "transfer film" which is "sticky but not too sticky" somewhere.

Prepare (clean, dry, lay out etc) the workpiece. Cut the vinyl to size with scissors etc. You can "weed" out the unwanted pieces at this stage, or manually remove them from the workpiece afterwards. Cleanly stick the transfer film to the top of the vinyl. The tricky part - now remove the backing from the vinyl, you should be left with the self-adhesive stuck to the transfer film. Stick the vinly to your workpiece! Enjoy!

tech details

linux

The cutter shows up as a standard USB<->RS-232 converter cable, and talks HP-GL.

The best software for printing (From Linux at least) is InkCut an InkScape extension. Simple convert stroke to paths, select what you want, and `Extensions->Cutter / Plotter->InkCut`. Click the 'Properties' top-right to set the correct serial port (probably /dev/ttyUSB0) and speed (defaults to 38400, but you can set it via the menu button and LCD on the cutter).

windows

Forget about Inkcut plugin, Inkscape will cut directly. Install drivers from http://www.microcontrols.org/arduino-uno-clone-ch340-ch341-chipset-usb-drivers/ (These work in Win10) Turn the printer on, then plug usb in Find Com? in device manager In Inkscape rotate your text to correct orientation, path>objects to path, right click and ungroup Click Extentions>Export>Plot... Set com? and baud 38400, when printer is zero'd and online then click apply and it should start cutting.

Planned Upgrades

Parts and upgrades that are planned/Budgeted/Purchased for in the near future


Graphtec Craft ROBO Caretakers

Maintainers

These are the people who look after and repair the Graphtec Craft ROBO, they're the ones to contact if there's any problems with it

Name Notes
Tony-S

Recent Changes

If you make any non-trivial changes to the Graphtec Craft ROBO or perform maintenance please note it here, delete records older than 1 yr